-
Created by Sunday, November 11, 2007 1:23 AM
Size: 500 × 326 (30 KB)
-
Wing mount shows 1/64" ply · Wing mount shows 1/64" ply doubler and 4-40 nylon mounting bolt.
Created by Saturday, November 10, 2007 10:12 PM
Size: 360 × 239 (9 KB)
-
Pushrods and antenna route · Pushrods and antenna route through tailboom.
Created by Saturday, November 10, 2007 10:08 PM
Size: 360 × 237 (10 KB)
-
Carbon fiber throwing peg · Carbon fiber throwing peg behind F-3 and above tailboom.
Created by Saturday, November 10, 2007 10:08 PM
Size: 360 × 238 (10 KB)
-
Completed airframe ready for · Completed airframe ready for covering and finish
Created by Saturday, November 10, 2007 10:08 PM
Size: 360 × 235 (13 KB)
-
Radio installation in second · Radio installation in second prototype.
Created by Saturday, November 10, 2007 10:08 PM
Size: 360 × 238 (9 KB)
-
Wing close-up showing mounting · Wing close-up showing mounting dowel.
Created by Saturday, November 10, 2007 10:08 PM
Size: 360 × 240 (8 KB)
-
Mark and drill for wing dowel · Mark and drill for wing dowel through F-2 into wing L.E.
Created by Saturday, November 10, 2007 10:02 PM
Size: 360 × 242 (9 KB)
-
Completed airframe showing · Completed airframe showing radio compartment.
Created by Saturday, November 10, 2007 10:02 PM
Size: 360 × 241 (8 KB)
-
Control horn angle guide used · Control horn angle guide used to set tilt.
Created by Saturday, November 10, 2007 10:02 PM
Size: 360 × 235 (6 KB)
-
Top sheeting being glued · Top sheeting being glued in place
Created by Saturday, November 10, 2007 10:02 PM
Size: 360 × 232 (9 KB)
-
Use stabilizer angle guide to · Use stabilizer angle guide to set V-Tail dihedral.
Created by Saturday, November 10, 2007 10:02 PM
Size: 360 × 236 (9 KB)
-
Ribs loosely in place prior to · Ribs loosely in place prior to final gluing
Created by Saturday, November 10, 2007 9:55 PM
Size: 358 × 185 (6 KB)
-
L.E. dowel glued in place. Wet · L.E. dowel glued in place. Wet front side with water to aid in bending.
Created by Saturday, November 10, 2007 9:55 PM
Size: 360 × 237 (9 KB)
-
Use W-1 angle guide for center · Use W-1 angle guide for center rib alignment for dihedral.
Created by Saturday, November 10, 2007 9:55 PM
Size: 360 × 243 (11 KB)
-
Trailing edge, wingtip, and bo · Trailing edge, wingtip, and bottom center sheeting pinned in place.
Created by Saturday, November 10, 2007 9:55 PM
Size: 360 × 191 (6 KB)
-
1" wide top sheeting strips in · 1" wide top sheeting strips in place over radio compartment
Created by Saturday, November 10, 2007 9:55 PM
Size: 360 × 234 (8 KB)
-
Fuselage sides glued around F- · Fuselage sides glued around F-2 and F-1.
Created by Saturday, November 10, 2007 9:48 PM
Size: 360 × 240 (8 KB)
-
Glue sides in place starting a · Glue sides in place starting at rear wedge and around F-3
Created by Saturday, November 10, 2007 9:48 PM
Size: 360 × 235 (8 KB)
-
Formers glued in place on fuse · Formers glued in place on fuselage bottom
Created by Saturday, November 10, 2007 9:48 PM
Size: 360 × 236 (10 KB)
-
Mark centerline and former loc · Mark centerline and former locations on fuselage bottom sheet.
Created by Saturday, November 10, 2007 9:48 PM
Size: 360 × 244 (9 KB)
-
Created by Saturday, November 10, 2007 9:48 PM
Size: 612 × 561 (33 KB)
